Sequence 5
output shaft
no preference
00 – none (bearingless)
01 – 25.40 [1.000] dia. straight shaft with .250-20unc-2b thread in end, 6.35 [.250] wide x 25.40 [1.000] dia. woodruff key
02 – 31.75 [1.250] dia. straight shaft with .375-16unc-2b thread in end, 7.938 [.3125] sq x 31.75 [1.250] straight key
03 – 31.75 [1.250] dia. .125;1 tapered shaft per sae j501 with 1.000-20 unef-2a threaded shaft end and slotted hex nut, 7.938 [.3125] sq x 25.40 [1.000] straight key
04 – 31.75 [1.250] dia. flat root side fit, 14 tooth, 12/24 dp 30 deg. involute spline with .375-16 unc-2b thread in end, 33.0 [1.30] minimum full spline length
05 – 25.40 [1.000] dia. 6b spline per sae j499 with .250-20unc-2b thread in end, 22.76 [.896] minimum full spline length
06 – 25.40 [1.000] dia. straight shaft with 10.31 [.406] dia. crosshole, 15.8 [.62] from end
07 – 22.22 [.875] dia. flat root side fit, 13 tooth, 16/32 dp 30 deg. sae b involute spline, 15.2 [.60] minimum full spline length
09 – 31.75 [1.250] dia. straight shaft with 10.31 [.406] dia. crosshole, 15.8 [.62] from end
14 – 31.75 [1.250] dia. straight shaft with (1.78 [.070] wide) retaining ring and .625-18unf-2b thread in end, 7.938 [.3125] sq x 31.75 [1.250] straight key
15 – 25.40 [1.000] dia. straight shaft with .250-20unc-2b thread in end, 6.35 [.250] wide x 25.40 [1.000] dia. woodruff key, corrosion resistant (seal area to shaft end)
16 – 32.00 [1.260] dia. straight shaft with m8 x 1.25-6h thread in end, 9.982 [.3930]w x 7.995 [.3132]h x 45.00 [1.772]l key
19 – 25.00 [.984] dia. straight shaft with m8 x 1.25-6h thread in end, 7.982 [.3142]w x 6.954 [.2738]h x 31.82 [1.254]l key
22 – 32.00 [1.260] dia. straight shaft with m8 x 1.25-6h thread in end, 9.982 [.3930]w x 7.995 [.3132]h x 45.00[1.772]l straight key, corrosion resistant (seal area to shaft end)
25 – 31.75 [1.250] dia. straight shaft with 13.49 [.531] dia. crosshole, 15.8 [.62] from end
26 – 31.75 [1.250] dia. .125;1 tapered shaft per sae j501 with 1.000-20 unef-2a threaded shaft end and slotted hex nut, 7.938 [.3125] sq x 25.40 [1.000] straight key, .180 extended shaft length
33 – 31.75 [1.250] dia. straight shaft with .375-16 unc-2b thread in end, 7.938 [.3125] sq x 31.75 [1.250] straight key, 9.52 [.375] extended shaft length
36 – 31.75 [1.250] dia. straight shaft with .375-16 unc-2b thread in end, 7.938 [.3125] sq x 31.75 [1.250] straight key (captured)
39 – none (bearingless) european spline
41 – 35.00 [1.378] dia. 10;1 tapered shaft per iso r775 with m20 x 1.5-6g threaded shaft end and slotted hex nut, 6.00 [.236] sq. x 20.00 [.787] key
55 – 31.75 [1.250] dia. straight shaft with .375-16 unc-2b thread in end, 7.938 [.3125] sq x 31.75 [1.250] straight key, hard chrome plated